Dreamwerks BLOG / ARTICLES

How to Measure and Fit Corner Shower Kits Safely

If your bathroom is on the smaller side, you've probably already looked into a corner-style shower unit. They're one of the easiest ways to fit a full shower into a tight space without losing floor room or sacrificing style. But before you grab your tape measure and start tearing into your old bathroom, there are a few things you need to know. Getting the measurements wrong, or skipping a step during setup, can turn a weekend project into a month-long headache. There are dozens of shower kits on the market today, and they all promise an easy weekend install. Some of them deliver on that promise. Others, not so much. This guide walks you through everything from measuring your space correctly to putting the final pieces together, so you end up with a shower that actually fits and works the way it should. Why Corner Units Make Sense for Small Bathrooms Corner units use the dead space in the corner of a room, which is often wasted otherwise. Instead of taking up a long stretch of wall, they tuck neatly into a 90-degree angle. This leaves more room for your vanity, toilet, or even just walking space. They also tend to look cleaner and more modern than a standard rectangular stall, which is a nice bonus if you're trying to boost your home's resale value. The tradeoff is that these units come in fairly specific sizes, so precision matters a lot more than it would with a standard shower. A half-inch error in your measurements can mean the difference between a smooth install and a return trip to the store. Material choice matters too. Acrylic panels are lightweight, warm to the touch, and easy to clean, which makes them a popular pick for first-time DIYers. Fiberglass tends to be a bit cheaper but can scratch more easily over time. If your budget allows, look for panels with a gel-coat finish, since they hold up better against soap scum and hard water stains. Whichever material you choose, double check that the panel thickness matches what your frame and base are designed to support, since mismatched parts are one of the more common return reasons at hardware stores. Tools You'll Need Before You Start Before you touch anything, gather your tools. You don't want to be halfway through a cut and realize you're missing a level. Here's a basic list: Tape measure (a laser measure works even better) Level Pencil and painter's tape for marking Caulk gun and silicone sealant Drill and screwdriver bits Utility knife Stud finder Adjustable wrench Most of these are things you probably already have in a toolbox. If not, they're inexpensive and worth owning for future projects anyway. How to Measure Your Shower Space Correctly Measuring is where most DIY shower projects go wrong. People eyeball it, round numbers up or down, or forget to check for square corners. Here's how to do it right. First, measure the length of both walls that form the corner where your unit will go. Don't just measure once - measure at the top, middle, and bottom of each wall. Walls are rarely perfectly straight, especially in older homes, and you want to know the smallest measurement so your unit actually fits. Next, check that the corner is actually square using a speed square or by measuring diagonally across the space in an X pattern. If the two diagonal measurements match, your corner is square. If they don't, you'll need to account for that gap when you install. Finally, measure the ceiling height in the shower area. Most units range from 70 to 78 inches tall, so you'll want to confirm your ceiling can accommodate the unit you're eyeing. Measuring for Complete Shower Kits Complete shower kits include the base, wall panels, and sometimes the door, all sized to fit together. This actually makes measuring simpler than buying pieces separately, because the manufacturer has already worked out how the base and walls line up. Just be sure to measure your rough opening against the kit's exact specifications before you order anything, since even "standard" sizes can vary slightly between brands. How to Install Shower Kit: Step-by-Step Guide Once you've got your measurements confirmed and your kit on hand, it's time for the actual build. Here's a simple breakdown of the process from start to finish. Step 1: Install Shower Base the Right Way Start with the base, since everything else builds on top of it. Set the base into the corner and check that it sits level in every direction - front to back and side to side. If it's not level, use shims underneath until it is. An uneven base leads to pooling water and drainage problems down the road, so don't rush this part. Once it's level, connect the drain according to the manufacturer's instructions, then apply a bead of plumber's putty or silicone around the drain fitting before securing it. Let everything set before moving forward. Step 2: Set Up the Shower Enclosure Kits Shower enclosure kits typically come with acrylic or fiberglass panels that snap or screw into a frame. Starting with one wall panel, line it up against the studs and base, check it's plumb with your level, then fasten it according to the included hardware. Repeat for the second wall panel, making sure both panels meet cleanly at the corner seam. This is also where you'll attach any shelving, grab bars, or accessories that came with your unit, since it's much easier to do this before the door goes on. Step 3: Install the Door and Seal Everything Hang the door or sliding panel last. Most kits use a track system that bolts to the top and bottom of the opening. Test that it slides or swings smoothly before fully tightening everything down. Once the structure is solid, run a clean bead of silicone along every seam - where the walls meet the base, where the walls meet each other, and around the door frame. This step is what keeps water inside the shower instead of seeping into your subfloor. Shower Kit Installation Safety Tips Shower kit installation isn't complicated once you know the steps, but there are a few safety details people often overlook. Always shut off your water supply before disconnecting any old plumbing. If you're working near electrical outlets or wiring, double-check that everything is properly grounded and up to code before you turn the water back on. Wear gloves when handling cut acrylic or fiberglass edges, since they can be sharp. And if you're cutting into drywall or removing an old shower, check for asbestos first if your home was built before the 1980s - it's a quick test that can save you a serious health risk later. Common Mistakes When You Install a Shower Kit Even careful DIYers run into trouble here. One of the biggest issues is rushing the leveling process. If you don't install shower base components level from the start, every other step gets harder, and you risk water pooling near the drain instead of flowing out properly. Another common mistake is skipping the manufacturer's instructions in favor of "winging it." Every kit is slightly different, and small details like screw spacing or sealant type can affect how long your shower lasts. Before you install a shower kit, check local building codes too - some areas have specific requirements for drain sizing or water shutoff valves that you'll need to follow. People also forget to dry-fit pieces before permanently attaching them. Setting panels in place temporarily, without screws or adhesive, lets you catch problems early instead of after everything is sealed. How to Install Shower Plumbing the Right Way Plumbing is usually the part that makes people nervous, but it doesn't have to be. Knowing how to install shower components correctly comes down to following the order: drain first, then supply lines, then the showerhead and controls last. Make sure your drain connection matches the trap below your floor, and always test for leaks by running water before you close up any walls. If you're not confident working with plumbing, this is one area where hiring a licensed plumber for an hour or two of help can save you from a much bigger repair bill later. Final Thoughts on Corner Shower Kits Now that you know how to install shower kit units the right way, fitting one into your bathroom is a project most homeowners can handle with the right prep work. The key is taking your time on the measurements, following your kit's specific instructions, and not skipping the sealing step at the end. Rushed corners - literally and figuratively - are where most problems start. We hope this guide helps you pick the right shower kits for your space and gives you the confidence to tackle the install yourself. With a level, some patience, and this checklist in hand, you'll have a shower that fits right and holds up for years to come.